|
|
|
Technical Service Bulletins If you have additional service questions, please call us at 800.968.0444 or 989.354-4111. If you have general technical service questions, not of an urgent matter, you can e-mail techservice@besser.com.
|
||
| NUMBER (Year-Number) |
DESCRIPTION |
PDF Format (Printer- Friendly) |
| 89-1 | 6, 9 and 10 yard slump mixer air/grease purged dust hubs |  |
| 89-2 | Quick reference guide for ordering AF-7 wear plates | |
| 89-3 | Vibrator motor sheaves for block machines | |
| 89-4 | Boston gear 700 series reducer lubrication | |
| 89-5 | SF-7 and SF-7W Cuber slider plate drive sprocket and wear bar adjustments | |
| 89-6 | Wire mesh belt installation and adjustment instructions | |
| 90-1 | New mixer blade sets of parts and installation procedure | |
| 90-3 | Quick reference guide for ordering agitator grids | |
| 90-4 | T-30 plant floor terminal set-up information | |
| 90-5 | Hydraulic tank liquid level switches | |
| 91-1 | Improved pneumatic control system for Bescodyne vibrators | |
| 91-2 | How the Trabon Air Grease Pump Works | |
| 91-3 | LSC-40 rotating cable anchor | |
| 92-1 | Putting Allen-Bradley SLC™-150 controllers back in the RUN MODE | |
| 92-2 | Adjusting second stop on Besser cam operated machines | |
| 93-1 | Quick order reference quide for mold pallet guides (Supercedes SB-No. 90-2) | |
| 93-2 | Besser NEMA and current transformer type | |
| 93-3 | Dip switch adjustments - Warner CBC-300 adjustable brake control | |
| 93-4 | The Bescodyne drive service tip | |
| 93-5 | Agitator encoder set-points | |
| 94-1 | Xycom 2050 Graphics display unit set-up information | |
| 94-2 | Extending life of Bescodyne units | |
| 94-3 | Update Bescodyne Clutch/Brake units from single to double air flow valve | |
| 95-1 | Check the Bescodyne Clutch/Brake stacks for wear | |
| 95-2 | Gemco cam limit switch boxes (Supercedes SB-No. 90-6) | |
| 95-3 | Modify Air Compaction Device air cylinders to reduce rod wear | |
| 95-4 | Instruction to move electrical box to left hand side of vibrator motor | |
| 95-5 | Using the Encoder for Allen-Bradley PLC®-2Progammable logic controller | |
| 95-7 | New style crossport and singling plate | |
| 96-2 | Mold compartment dimensions | |
| 96-3 | Descriptions and examples of how to order mold parts | |
| 96-4 | Besser Mold assembly and torque requirements | |
| 96-5 | V3-12 Pinion shaft assembly (Besser No. 464229) installation w/locking assembly | |
| 97-1 | Using the Encoder for Allen-Bradley SLC™-500 programmable logic controllers | |
| 97-2 | Achieving peak hydraulic system efficiency | |
| 97-3 | SLC™-500 programmable controller | |
| 97-4 | Updated adjustments for 5-5/8" high units on a V-4 or V-4 (26"deep machine) | |
| 97-5 | Recommendations for use of Vibrator weights | |
| 97-6 | Portable Mold Jig | |
| 98-1 | Xycom 2050 Graphics Display Unit set-up information for use with a PLC® | |
| 98-2 | AFC SmartPac® Operating Instructions (Supercedes SB-No. 95-6 and SB-No. 96-1) | |
| 99-1 | Breather Vent and Split Oil Seal | |
| 99-2 | Installing Screen Program in PanelView™ 900/1000 with a Flash Card | |
| 00-1 | Installation of KAMCO box (to replace GEMCO box) | |
| 00-2 | Bull & Pinion Gear Clearance and Alignment Procedure for MK3 Style Pinion Shafts | |
| 00-3 | Besser-Matic® 1305 Frequency Drive Programming Instructions | |
| 00-4 | Procedure to Align Carriage and Ball Screw | |
| 00-5 | Open Rotor Test | |
|
Improved Vibrator Bolts |
|
|
